Study on Cutting Parameters to Reduce the Surface Roughness in Hard Turning of SKD 61 Steel using Taguchi Method
T. Lam. INTERNATIONAL JOURNAL OF TREND IN SCIENTIFIC RESEARCH AND DEVELOPMENT, 6 (4):
568-571(June 2022)
Abstract
In this article, the Taguchi method was used to optimize cutting parameters to achieve minimum roughness during hard turning of SKD 61 steel. Cutting parameters selected include cutting speed, feedrate, and depth of cut. Experiments were organized by the use of L9 orthogonal array. The influence of each factor on the output response is analyzed by Minitab software. Signal to noise and analysis of variance are applied to statistical analysis. The result indicates that the feedrate has an outstanding influence compared to the other two variables. Optimal processing conditions to achieve the minimum roughness has been given. In addition, a regression equation describing the relationship between roughness and cutting parameters was built with the determination coefficient R sq of 93.99 . Thanh-Dat Phan | The-Vinh Do | Duong Huong Lam "Study on Cutting Parameters to Reduce the Surface Roughness in Hard Turning of SKD 61 Steel using Taguchi Method" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-6 | Issue-4 , June 2022, URL: https://www.ijtsrd.com/papers/ijtsrd50073.pdf Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/50073/study-on-cutting-parameters-to-reduce-the-surface-roughness-in-hard-turning-of-skd-61-steel-using-taguchi-method/thanhdat-phan
%0 Journal Article
%1 noauthororeditor
%A Lam, Thanh-Dat Phan | The-Vinh Do | Duong Huong
%D 2022
%J INTERNATIONAL JOURNAL OF TREND IN SCIENTIFIC RESEARCH AND DEVELOPMENT
%K 61 SKD Taguchi cutting dry hard method roughness steel surface tool turning
%N 4
%P 568-571
%T Study on Cutting Parameters to Reduce the Surface Roughness in Hard Turning of SKD 61 Steel using Taguchi Method
%U https://www.ijtsrd.com/engineering/mechanical-engineering/50073/study-on-cutting-parameters-to-reduce-the-surface-roughness-in-hard-turning-of-skd-61-steel-using-taguchi-method/thanhdat-phan
%V 6
%X In this article, the Taguchi method was used to optimize cutting parameters to achieve minimum roughness during hard turning of SKD 61 steel. Cutting parameters selected include cutting speed, feedrate, and depth of cut. Experiments were organized by the use of L9 orthogonal array. The influence of each factor on the output response is analyzed by Minitab software. Signal to noise and analysis of variance are applied to statistical analysis. The result indicates that the feedrate has an outstanding influence compared to the other two variables. Optimal processing conditions to achieve the minimum roughness has been given. In addition, a regression equation describing the relationship between roughness and cutting parameters was built with the determination coefficient R sq of 93.99 . Thanh-Dat Phan | The-Vinh Do | Duong Huong Lam "Study on Cutting Parameters to Reduce the Surface Roughness in Hard Turning of SKD 61 Steel using Taguchi Method" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-6 | Issue-4 , June 2022, URL: https://www.ijtsrd.com/papers/ijtsrd50073.pdf Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/50073/study-on-cutting-parameters-to-reduce-the-surface-roughness-in-hard-turning-of-skd-61-steel-using-taguchi-method/thanhdat-phan
@article{noauthororeditor,
abstract = {In this article, the Taguchi method was used to optimize cutting parameters to achieve minimum roughness during hard turning of SKD 61 steel. Cutting parameters selected include cutting speed, feedrate, and depth of cut. Experiments were organized by the use of L9 orthogonal array. The influence of each factor on the output response is analyzed by Minitab software. Signal to noise and analysis of variance are applied to statistical analysis. The result indicates that the feedrate has an outstanding influence compared to the other two variables. Optimal processing conditions to achieve the minimum roughness has been given. In addition, a regression equation describing the relationship between roughness and cutting parameters was built with the determination coefficient R sq of 93.99 . Thanh-Dat Phan | The-Vinh Do | Duong Huong Lam "Study on Cutting Parameters to Reduce the Surface Roughness in Hard Turning of SKD 61 Steel using Taguchi Method" Published in International Journal of Trend in Scientific Research and Development (ijtsrd), ISSN: 2456-6470, Volume-6 | Issue-4 , June 2022, URL: https://www.ijtsrd.com/papers/ijtsrd50073.pdf Paper URL: https://www.ijtsrd.com/engineering/mechanical-engineering/50073/study-on-cutting-parameters-to-reduce-the-surface-roughness-in-hard-turning-of-skd-61-steel-using-taguchi-method/thanhdat-phan
},
added-at = {2022-08-10T14:14:38.000+0200},
author = {Lam, Thanh-Dat Phan | The-Vinh Do | Duong Huong},
biburl = {https://www.bibsonomy.org/bibtex/2378255c7d9a49fccdacc39fb8bd8665c/ijtsrd},
interhash = {5d0ea9ef45a964fc142ffad002579e64},
intrahash = {378255c7d9a49fccdacc39fb8bd8665c},
issn = {2456-6470},
journal = {INTERNATIONAL JOURNAL OF TREND IN SCIENTIFIC RESEARCH AND DEVELOPMENT},
keywords = {61 SKD Taguchi cutting dry hard method roughness steel surface tool turning},
language = {english},
month = {June},
number = 4,
pages = {568-571},
timestamp = {2022-08-10T14:14:38.000+0200},
title = {Study on Cutting Parameters to Reduce the Surface Roughness in Hard Turning of SKD 61 Steel using Taguchi Method
},
url = {https://www.ijtsrd.com/engineering/mechanical-engineering/50073/study-on-cutting-parameters-to-reduce-the-surface-roughness-in-hard-turning-of-skd-61-steel-using-taguchi-method/thanhdat-phan},
volume = 6,
year = 2022
}